How Much Does It Cost to Pave a Gravel Driveway?

In this guide

Gravel Driveway Cost Calculator

Gravel Driveway Cost Calculator

Costs to pave a gravel driveway vary greatly by region. Let’s calculate the cost for your zip code.

Zip code

CALCULATE

Want to receive more accurate estimates for your project?

REQUEST QUOTES

NATIONAL COSTS

Average Cost

$2,277

Low Cost

$835

High Cost

$6,768

See Gravel Driveway Cost Calculator Breakdown 

Average Cost Project Low-Cost Project High-Cost Project

Cost

Material

Hot mix for a 10' x 10' driveway at 3" thick

$669

Labor

Pouring, spreading, and raking smooth 100 sq.ft. of 3" hot mix

$166

Material

Hot mix for a 10' x 27' driveway at 3" thick

$1,826

Labor

Pouring, spreading, and raking smooth 270 sq.ft. of 3" hot mix

$451

Materials

3,000 PSI concrete, wire mesh, and vapor barrier for 560 sq.ft.

$3,113

6" aggregate crushed stone base for 560 sq.ft.

$762

Labor

Pouring, finishing, and curing 560 sq.ft. of 4" concrete slab

$2,437

Pouring and spreading 6" aggregate base for a 14' x 40' concrete driveway

$228

Fine grading 560 sq.ft.

$228

Total

$835

$2,277

$6,768

What Is Driveway Paving?

There are many different ways to create a driveway. A driveway that is paved is different from a driveway that has been built or created with gravel. In a gravel driveway, the driveway has been built up with three layers of differently sized gravel to facilitate good drainage.

In a paved driveway, it may start with a gravel base, but then have a hard, stationary material applied over it, such as asphalt or concrete. If you have an existing gravel driveway, you can refurbish it with additional gravel, remove the gravel entirely and start with a new base, or pave the gravel by applying asphalt or another mixture directly on top of the gravel, allowing the gravel to act as a base for the asphalt driveway.

Paving a gravel driveway costs more than adding fresh gravel to rebuild your existing gravel drive. However, a paved driveway lasts longer with less maintenance than a gravel driveway, and it is easier to plow and snow blow in the winter months.

Gravel Driveway Paving Cost by Surface Type

If you have an existing gravel driveway, you can pave it with multiple surfaces, depending on the desired finish and appearance. Each surface has a different associated cost, maintenance, longevity, and even paving process:

Convert Gravel Driveway to Tar-and-Chip

The simplest way to pave a gravel driveway is to do a tar-and-chip seal directly on top of the existing gravel. Tar-and-chip comes in multiple grades, from a very thin layer of hot asphalt poured over the gravel with additional aggregate added to two thicker layers of hot asphalt with aggregate added. This is a tough, durable driveway, but it is not smooth and cannot be snow blown. It lasts longer without cracking than asphalt and does not migrate like gravel. It costs $1 - $5 a square foot installed, with an average of $3 a square foot for most driveways.

Convert Gravel Driveway to Asphalt

This is the most common method of paving a gravel driveway, particularly in the northern states and colder climates. If the existing gravel driveway has a good base and was correctly installed, it is possible to pave with asphalt directly over it. If the driveway has lost most of its gravel or is not level, you may first need to remove the gravel and start again. The average cost to asphalt a gravel driveway is between $2 and $6 a square foot.

Convert Gravel Driveway to Concrete

Converting gravel to concrete is a more common driveway method in the south and warmer climates. Concrete does better in hot climates than asphalt and lasts much longer than either asphalt or gravel. It is also lower in maintenance than both but costs more, nearly twice as much as paving with asphalt in some cases. The cost to pave a gravel driveway with concrete is between $4 and $10 a square foot on average.

Gravel Driveway Paving Process

Much of the process and cost of paving a gravel driveway comes down to the condition that the driveway is in at the paving time. Some well-maintained gravel driveways with a good base and grading may be paved without removing the gravel or only needing to remove the top layer of gravel.

If the driveway is in poor condition, has holes or divots, is not draining well, or needs to be regraded, then the gravel must first be removed. In this case, the driveway is graded, and then a new base material is put down. This may be gravel, and in some cases, your existing gravel is reused.

Once the base is down, the asphalt is poured and spread, then rolled and edged. Sometimes, you may have a second coat put down after the first one cures, particularly if you want the driveway to last longer or if it will get a lot of use.

It may be a few days before you can drive or park on your driveway, and it may be up to a year before the final curing is complete.

Solid vs Stone Surfaces for Driveways

While driveways are created in several ways, they tend to break down into two distinct categories - solid-surface driveways like asphalt and concrete and aggregate driveways like gravel or stone. Within each category, you have several options, but there are some broad similarities within each option to help decide which category best fits your needs.

Solid-surface driveways are hard and durable. They can be smooth like asphalt and concrete or more textured like tar and chip. They last 20 - 30 years on average when well-maintained. Asphalt is higher in maintenance than concrete, requiring a sealant every few years, but solid surface driveways are lower in maintenance than aggregate driveways like gravel.

Aggregate and stone driveways need to be raked each year to move the migrating stones back into position. They are harder to shovel and plow, and each spring, the gravel needs to be relocated.

They also require added fresh aggregate every few years to top up the surface. When they are well-maintained, they are beautiful and give your home a distinctive look. They also tend to be lower in upfront costs but cost more long term in maintenance than a solid driveway.

Gravel vs Asphalt Driveway

An asphalt driveway is the second least expensive driveway type, with gravel as the least expensive. It is also the second highest in maintenance, just behind gravel. So when you convert from gravel to asphalt, you do less maintenance, but you pay slightly more for the driveway to be finished. If you live in a snowy area, an asphalt driveway is easier to shovel and plow than a gravel driveway. If you live in a hot climate, the gravel holds up better than asphalt because it does not soften in the heat.

Gravel vs Concrete Driveway

While gravel is the highest maintenance and lowest cost for driveway materials, concrete is nearly the opposite. It is one of the lowest maintenance and highest priced driveway materials. Concrete lasts for years with very little maintenance, far outlasting a gravel driveway. It does not perform well in freeze/thaw conditions because it develops cracks and potholes, while gravel is less likely to be affected.

Enhancements and Improvement Costs

Landscaping

Gravel often migrates, which means that the area around your driveway is likely filled with excess gravel. After paving, you may want to bring in a landscaper to edge your new driveway and clean it up, getting it in better condition. The cost of hiring a landscaper is $50 to $100 an hour.

Colored Pavement

Both concrete and asphalt may be tinted or colored to give you a more decorative driveway. Add color to your new driveway for an additional $2 a square foot on average.